Frequently Asked Questions

What are the typical fluids I can dispense?

There are not many materials that cannot be dispensed in one form or another. Please call us if you would like advice but our experience has been to supply systems for accurately handling adhesives, cyanoacrylates, anaerobics, solvents, chemical, sealants, silicones, epoxies, resins, pastes, solders, fluxes, hot melts, PVA's, UV cure, conformal coatings, primers, activators, water based, contact type, braze and conductive adhesives. We have equipment for single and two part liquids, cold or hot melt glues, pastes, watery liquids and sprayable fluids. And we have many customers using low cost dispensing systems as well as though running our robot systems.

What is the best system for cyanoacrylates?

The TS255 dispenser will apply all CAs direct from syringe barrels up to 55cc size. Use the TS5622VU with a pressure pot and TS350 controller for higher volume deposits of CA's.  Use Teflon Lined tips for no clogging.

Do you supply adhesives and other chemicals?

Many of our customers ask us to provide them with materials as well as dispensing equipment and accessories. Our partnerships with adhesive manufacturers and the fact we supply them with dispensing equipment allows us to supply adhesives, silicones, epoxies, UV cure and many other liquids at special prices.

How do your prices compare to others?

We don't hide our prices and you can order items on account from us as well as online. Our pricing is very competitive but if you notice a product your require a specific quote on or it is high volume, please tell us and we'll do something about it.

How long are lead times?

Almost all barrels, cartridges, needles, tips, nozzles, fittings and dispensers are available from stock. We also stock a wide range of guns, valves, tanks, fluid lines and accessories. Some items take longer. Some valves up to 5 days. Robots are built to order and we always quote 4-5 weeks but we sometimes have machines in stock. Some filled syringes and cartridges can take up to 5 weeks if we are waiting on the raw materials from the manufacturer very much but in many cases it is quicker.

What does silicone free mean?

When a company does not offer silicone free barrels, cartridges, nozzles and tips - it might mean that cheaper low grade products are being supplied instead. Some of these will have been manufactured in production facilities where silicone release agents find their way onto the plastics. So when you use the components with your adhesives, it can affect the performance.

What does industrial grade mean?

All syringe barrels, cartridges, tips, nozzles, etc are safe for 'industrial' use up to 100 psi. Hypodermic syringes are thin walled whereas industrial grade barrels have thick moulded walls.

Can I re-use barrels, etc?

In short, yes you can. But re-use will weaken them and could be unsafe. Also, cured adhesive can mix with fresh material causing failures and contamination. And if a lot of time is spent cleaning low cost components, it is no doubt cheaper to dispose of and replace with new. If you are paying too much for these components, talk to us and we'll offer cost effective pricing plans.

How do I select the right piston for the syringe barrel?

For our air-powered dispensers, select the 700 series syringe barrels in sizes from 3cc to 55cc, either clear (natural), amber (UV tint) or black (UV block). For watery liquids that drip, use our white wiper pistons. They create a nice tight seal in the barrel and hold the liquids in place. For most other general adhesives and liquids, use our blue easy flow pistons. They are not so tight and allow a smooth movement both down and up. This prevents oozing of liquids after the deposit has been made. For very thick materials and stringy contact-type adhesives, use our red pistons. These have flat walls and will not get stuck to the inner barrel wall when dispensing.

Do all dispensers require an air supply?

No. Our manual syringe guns and cartridge guns do not. And the LDS9000 air-free syringe dispenser requires no air supply.

We work in a explosive production area and cannot have electric dispensers?

Use the TS924 footvalve dispenser for pastes, gels and adhesives. It is non electric and offers a controlled method of dispensing direct from syringe barrels. Use the TS924V for thinner liquids as this version includes a vacuum suckback. Use any of our manual or pneumatic syringe or cartridge guns safely in an explosive area. Or our TS1201 dispensing pen with any of our pressure pots.

Prices are in £ Sterling GBP and exclude VAT which is charged on UK orders at checkout. Orders are encrypted on a 128 bit secure server for total security. All personal information and payment details is encrypted on SSL secure website pages. Statements, technical information and recommendations contained herein are based on tests we believe to be reliable but they are not to be construed in any manner as warrantees expressed or implied. The user shall determine the suitability of the product for his intended use and the user assumes all risk and liability whatsoever in connection therewith.